Ubiquiti UniFi UAP-NANOHD AC NanoHD Wave 2 Wi-Fi Access Point
- Dual Band Access Point
- 200+ client capacity
- Powered by 802.3af PoE
The UniFi Ubiquiti UAP nanoHD is a compact, dual-band access point that can reach a 2+ Gbps aggregate throughput rate with its 5 GHz and 2.4 G bands (Read more)
The Ubiquiti UAP nanoHD is a compact, dual-band access point that can reach a 2+ Gbps aggregate throughput rate with its 5 GHz (4x4 MU-MIMO) and 2.4 GHz (2x2 MIMO) bands. The UAP nanoHD can also support over 200 concurrently connected clients while maintaining an even, reliable wireless experience across your entire network. With its elegant, nano-sized design, this access point can be staged virtually anywhere indoors where you'd like to enhance your wireless speed and performance. Built for plug-and-play simplicity, the UAP nanoHD can be set up in minutes and fully managed with the UniFi Network web application or mobile app.
With the UniFi Controller software running in a NOC or in the cloud, administrators can manage multiple sites: multiple, distributed deployments and multi-tenancy for managed service providers. Below are some deployment examples.
Scalable Enterprise Wi-Fi Management
UniFi® is the revolutionary Wi-Fi system that combines enterprise performance, unlimited scalability, and a central management controller. The UniFi nanoHD AP has a refined industrial design and can be easily installed using the included mounting hardware. Easily accessible through any standard web browser and the UniFi app (iOS or Android™), the UniFi Controller software is a powerful software engine ideal for high-density client deployments requiring low latency and high uptime performance. Use the UniFi Controller software to quickly configure and administer an enterprise Wi-Fi network - no special training required. RF map and performance features, real-time status, automatic UAP device detection, and advanced security options are all seamlessly integrated.
Initial 802.11ac Wave 1 SU-MIMO (Single-User, Multiple Input, Multiple Output) technology allows an earlier-generation AP, such as the UniFi AC Pro AP, to communicate with only one client at a time. 802.11ac Wave 2 MU-IMO (Multi-User, Multiple Input, Multiple Output) technology allows a Wave 2 AP, such as the UniFi nanoHD AP, to communicate with multiple clients at the same time - significantly increasing multi‑user throughput and overall user experience.
The following describes a 5-client scenario:
MU-MIMO Assuming the same conditions, a Wave 2 AP provides up to 75% improvement1 overall over a Wave 1 AP. This improvement increases wireless performance and/or serves more clients at the same performance level.
4x4 Spatial Streams
At any single time, a Wave 2 AP can communicate with the following MU-MIMO clients:
• four 1x1 clients
• two 2x2 clients
• one 2x2 client and two 1x1 clients
• one 3x3 client and one 1x1 client
A 4x4 Wave 2 AP delivers up to 33% greater performance than a Wave 1 AP that is 3x3 in both radio bands.
The UniFi nanoHD AP is the UniFi 802.11ac Wave 2 AP with the smallest form factor. Combining the performance increases from MU-MIMO technology and the use of 4x4 spatial streams, the UniFi nanoHD AP delivers up to 25% greater performance than a typical Wave 1 AP.
For optimal performance, use MU‑MIMO clients. SU‑MIMO clients will also benefit and gain up to 10-20% greater performance when used with the UniFi nanoHD AP.
- Four-stream, 802.11ac Wave 2 WiFi technology
- 5 GHz (4x4 MU-MIMO) band with a 1.733 Gbps throughput rate
- 2.4 GHz (2x2 MIMO) band with a 300 Mbps throughput rate
- 200+ concurrent client capacity
- Powered by 802.3af PoE (PoE injector included with single pack)
||160 x 160 x 32.65 mm (6.3 x 6.3 x
With Mounting Kits
|300 g (10.6 oz)
315 g (11.1 oz)
||(1) RJ45 GbE
||(1) Reset to Defaults
||UniFi Switch (PoE)
|Maximum Power Consumption
|Supported Voltage Range
||44 to 57VDC
(2) Single-Port, Single-Polarity Antennas, 2.8 dBi each
(2) Single-Port, Dual-Polarity Antennas, 3 dBi each
||WEP, WPA-PSK, WPA-Enterprise (WPA/WPA2,
||8 per Radio
||Wall/Ceiling (Kits Included)
||-10 to 70° C (14 to 158° F)
||5 to 95% Noncondensing
||CE, FCC, IC
||Per-User Rate Limiting
|Guest Traffic Isolation
||Voice, Video, Best Effort, and Background
|Supported Data Rates
||6, 9, 12, 18, 24, 36, 48, 54 Mbps
||6.5 Mbps to 300 Mbps (MCS0 - MCS15, HT 20/40)
||6.5 Mbps to 1.7 Gbps (MCS0 ‑ MCS9 NSS1/2/3/4, VHT
58 Mbps to 1.7 Gbps (MCS0 ‑ MCS9 NSS1/2, VHT 160)
||1, 2, 5.5, 11 Mbps
||6, 9, 12, 18, 24, 36, 48, 54 Mbps
|-- No videos available --|
|Ubiquiti UAP-NANOHD datasheet|
|Ubiquiti support site|
Get expert answers to questions specific to this product below or for more help visit our Q & A forum
Be the first to ask a question and help others interested in this product
Your feedback helps us improve our products and services as well as helping other users make informed buying decisions.
There are no reviews for this product.
Why buy from Connectec?
Our technical support team are experienced installation engineers with years of field experience.
Customer service is our top priority. We always try to ensure we offer a first class service too all our customers.
We offer FREE mainland UK delivery on orders over £75 and FREE next day delivery on orders over £150*.
* Qualifying products only, subject to terms. For more information view our delivery information.