Pre-terminated Internal Loose Tube Fibre Optic Cable
- Double ended preterm
- 900µm loose tube
- Kevlar Pulling socks
Pre-terminated 900µm loose tube fibre optic cable available in single mode OS2 or multi-mode OM1, OM2, OM3 and OM4 with up to 24 cores. (Read more)
Pre-term fibre optic cable is a great way to access all the benefits of a professional fibre optic installation without requiring any advanced skills or professional termination equipment.
Our pre-terminated fibre is available as standard tight buffered or loose tube fibre for everyday use or as CST and SWA for more rugged installations. Each type of cable is available as single-mode OS2 for longer cable distances or multi-mode OM1, OM2, OM3 or OM4 for shorter high bandwidth installations and with fibre counts of 8 to 96 cores.
You can select to have your pre-term fibre terminated using either standard ST, SC, LC or FC fibre connectors or APC variants of the connectors for highly sensitive applications.
To ensure durability of the fibre cable during installation the cable has an epoxy bonded gland on each end with a Kevlar strain relief yarn and a protective sleeve protecting the connectors. This makes the cable extremely tough and protects the cable from the high tension loads experienced such as when pulling the cable through ducting.
Installation of pre-terminated fibre is quick and easy and requires no special skills or equipment. Simply remove the protective sleeve and thread the connectors through the cable entry hole in the fibre enclosure. Secure the gland to the drawer to provide additional protection after installation and connect the connectors into the outlets in the enclosure. If cable channelling is available within the enclosure it is advisable to lay the inner fibre cores into the channelling for further protection.
Loose tube fibre
In a loose tube fibre cable the inner fibre cores are suspended in a gel. This provides protection from moisture and temperature, prevents freezing and allows the cable to expand and contract with changes in temperature without damaging the inner cores. Loose tube fibre cable is ideally suited for outdoor installation. Despite being moisture resistant however loose tube cable is not recommended for installation underwater.
For additional protection outdoors you can upgrade from standard loose tube cable to CST cable or for the ultimate in protection you can use SWA cable.
Loose tube fibre cables are tough, thick and relatively rigid cables which makes them less suited to installation indoors where tight buffered cables would be a better choice.
Fibre Optic Cable Recommended Installation Distances
Different fibre optic cables are capable of achieving faster speeds over longer distances. Depending on your application use the table below as a guide to selecting the right cable for your installation.
Fibre Connector Choices
Selecting the right connector is often governed by compatibility with the equipment that is being connected. For new installations the compact LC connector is a good choice thanks to it's small size and common use on modern networking hardware.
Locking fibre connector found on legacy devices such as switches and data-communications equipment.
Still widely used in fibre installations although newer hardware typically has switched to the more compact space saving LC alternative.
More compact connector found in high density installations and on modern switches and transceivers. This is the most common type of connector currently in use.
Telecommunications connectors with good mechanical isolation although now mostly replaced by SC and LC connectors.
|Loose Tube Fibre Specifications|
|Jacket||Fire retardant FRNC/LSZH
Water and UV resistant
IEC 60332-1, IEC 61034, IEC 60754
||Single mode OS2 / Mulit Mode OM1, OM2, OM3, OM4
|Crush resistance||2000 N / 10 cm|
|Impact resistance||3 Impacts (w/20N.m)|
|Min bend radius
||15 x Cable diameter|
|Min bend radius load
||20 x Cable diameter|
|Temperature range||Installation -5°C to +50°C
Operation -20°C to +70°C
Storage -30°C to +70°C
|Nominal weight||49 kg/km|
|Standard put-up length||2100m, 4100m|
|Loose tube diameter||3.0mm|
|Outer jacket thickness||1.3 +/- 0.3mm|
|Cable outer diameter||6.4 +/- 0.5mm|
|-- No videos available --|
|Loose tube fibre datasheet|
|Pre-terminated fibre datasheet|
|Connectix support site|
Get expert answers to questions specific to this product below or for more help visit our Q & A forum
Be the first to ask a question and help others interested in this product
Your feedback helps us improve our products and services as well as helping other users make informed buying decisions.
There are no reviews for this product.
Why buy from Connectec?
Our technical support team are experienced installation engineers with years of field experience.
Customer service is our top priority. We always try to ensure we offer a first class service too all our customers.
We offer FREE mainland UK delivery on orders over £75 and FREE next day delivery on orders over £150*.
We are approved Connectix resellers for direct access to manufacturer warranty and support.
* Qualifying products only, subject to terms. For more information view our delivery information.